DAV Class 7 Science Solutions: Electric Current and Its Effects

Electricity And Its Effects Solutions

In this section, we will discuss the Class 7 Science book Solutions of DAV school book. We have given detailed answers to the back exercise questions of Chapter Electricity and Its Effects. If you face any problem, you can ask your doubts through the comments section below or connect with Careeradvice4u on Facebook.

 

Class 7 DAV Science Solutions | Page 261, Part D

Question 1: The bulb in the circuit shown in the figure does not glow. Why? Redraw the circuit diagram by making the necessary changes in it, so that the bulb starts glowing.

Open circuit diagram

Ans 1: The bulb in the circuit does not glow because the switch is in open mode. The switch needs to be in closed mode in order to make the bulb glow. The circuit could not be closed in this position.

 

Closed Circuit class 7

Ques 2: Name three practical devices based on the heating effect of current

Ans: Three devices which are based on the heating effect of electric current are:-

Toaster

Electric Iron: It also works on the principle of heating effects of electric current.

Electric Bulb: The filament of the bulb gets heated up when electricity is passed through the bulb.

 

Ques 3: Write two special characteristics of the wire needed for making the ‘element’ of an electric heater.

Two special characteristics of the wire needed for making an element of electric heater are:-

  1. It should have a high melting point
  2. It should have high resistivity
  3. It should not burn out when it attains a very high temperature

These properties can be seen in Nichrome. so, nichrome is used for making the element of the heaters. Nichrome is an alloy that is made up of Nickel and Chromium.

Don’t Miss: Transportation in Plants and Animals Solutions

 

Question 4: Give the meaning of the term ‘Short-circuiting’ and ‘overloading’ in an electric circuit?

Ans 4: Short Circuit occurs when the live and neutral wire touch each other. This may happen due to the weak insulation of the wires.

Overloading: When we connect more than one appliance to a single socket then it can cause overloading. The single-socket may not be able to handle all the devices at a single time.

 

Question 5: Do you think an electromagnet can be used for separating plastic bags from a garbage heap? Explain.

No electromagnet can not be used to separate from the plastic bags because they do not contain metal ( iron). To separate substances using electromagnet the substances should be made up of iron.

 

Question 6: State three applications of Electromagnet.

1. Electromagnets are used to lift heavy objects which are made up of iron. They can be used to transfer iron rods from one place to another.

2. We use electromagnets in electric bells and loudspeakers.

3.  A lot of toys work on the principle of electromagnetism.

 

Part E Ch: Electric Current and Its Effects Solutions

Question 1: The same amount of current flows through the connecting wires and the bulb filament. However, it is only the filament that glows. Why?

Ans: The filament of the bulb is made up of Tungsten which has very high resistance so it heats up quickly. The connecting wire is a good conductor so it conducts electricity and does not gets heated up.

 

Question 2: The brightness of light, emitted by a bulb, is observed to decrease when an electric heater is connected in series with it. Suggest the likely reason for this observation.

Ans: When an electric heater is connected in series with the electric bulb then the power dissipated in the bulb is lesser as compared to the situation when the heater was not connected. This happens because the voltage for the bulb will be reduced. Less voltage means current flowing through bulb will reduce a bit and the bulb will become dimmer.

 

Question 3: Suggest an experimental setup to illustrate the action of an electric fuse. 

Ans 3:

Setup to illustrate the action of an electric fuse
Setup to illustrate the action of an electric fuse

 

  1. Take an aluminium foil
  2. Take two nails and connect them in the circuit as shown in the diagram
  3. Put Fix the aluminium foil on the top of the nails and then turn on the switch.
  4. As the current start flowing in the circuit, the aluminium foil will burn quickly.

This is the way, an electric fuse works.

 

Question 4: A novice electrician, while carrying out some repairs in Sumit’s house, tried to put a tungsten wire in a fuse. Sumit’s father on noticing this, stopped him from doing so. Give reasons as to why he did that. 

Ans: Tungsten should not be used in the fuse because a fuse requires a low melting point so that it can burn up when the current exceeds the normal limit. This prevents accidents when excess current flows. Tungsten has a high melting point and it will not melt fast and this thing can lead to damage to appliances.

 

Question 5: Draw a labelled diagram of an electric bell and explain its functioning. 

Ans 5:

Labelled diagram of an electric bulb
Labelled diagram of an electric bulb

 

The iron core serves as an electromagnet when you allow electric current to flow through the circuit. The soft armature is attracted by the electromagnet and this enables the striker to hit the bell. The bell produces a sound. The armature returns back to its original position due to the action of the spring and iron core stops to act as an electromagnet. When the switch is pressed again, then the current again flows through the circuit, iron core again serves as an electromagnet and the repeat of the same actions which makes the bell produce sound. So, this was the functioning of an electric bell.

 

 

 

 

 

 

 

 

Deepak Kumar

Deepak Kumar is the founder of careeradvice4u.com. He is a Professional Blogger, web designer, and a teacher too. He has done Computer Science from Delhi University and has 8 years of teaching experience. He teaches various subjects upto XII class and above that also. He had in his mind from a very long time to use his blogging passion for the help of School, college students, and other job seekers. Careeradvice4u will bring to you all the information and stuff that you need to shape up your career. He is also the founder of successfully growing tech blog: techadvises.com and also runs his own Web Solutions company, xPress Web Solutions, which deals in all types of web solutions- Web designing, development and Android apps designing.

below post

1 Trackback / Pingback

  1. DAV Science Solutions Class 7: Transportation in Plants and Animals - CAREERADVICE4U

Leave a Reply

Your email address will not be published.


*


This site uses Akismet to reduce spam. Learn how your comment data is processed.